The Faqs Of The Engineered Wood Flooring

1.how to handle the floor generation gap in winter 
Woodiness floor is formed by lumber, lumber has a very big characteristic is dry shrink wet bilge. Especially during winter heating, as a result of indoor humidity drop, the floor wood fiber will have a certain contraction, the gap generated at this time can be adjusted to restore. It is recommended that you often wipe the floor with a wet mop without dripping water, or use a humidifier to ensure that the indoor air humidity is between 45%-75%. After observing the above practices for a period of time, if the gap does not gradually recover, you can contact us.

2.What are the requirements for the interior environment before floor paving?
. Ensure that the ground is smooth before paving (use a two-meter ruler to detect the ground flatness, and the measured value is required to be ≤3mm/2m). Use a moisture content tester to detect the ground moisture content, and the common ground moisture content is ≤20%, and the geothermal ground moisture content is ≤10%.
. Other decoration works in the house should be completed as far as possible to avoid cross-work or damage to the floor by other works after floor paving.
Requirements for the reserved height of the door: if the floor and the threshold stone are connected by buckles, the reserved height should be within 2mm from the finished height of the floor after pavement. If there is no buckle connection, the reserved height should be equal to or slightly higher than the finished surface of the floor.

3.What are the key points of acceptance after floor laying?
After the floor is laid, the user checks the pavement effect to make sure that the pavement is smooth, there is no damage or obvious scratches on the surface, and there is no obvious abnormal sound in the main walking area. Finally, the user signs for acceptance.
Solid wood floor acceptance standard: floor assembling height difference ≤0.6mm; Seam width ≤0.8mm.
Solid wood multi-layer floor acceptance standard: floor assembly height difference ≤0.20mm (without chamfering) /≤0.25mm (with chamfering); Seam width ≤0.40mm.
Reinforced composite floor acceptance standard: floor assembly height difference ≤0.15mm; Seam width ≤0.20mm.

4.How does sound appear long after floor is spread handle?
If the shop is installed after the use of time is not long, different sound may be wood fiber friction sound, this kind of sound can disappear gradually in the use process. If it has been a long time, but the floor still has a sound, you can contact us when we feedback maintenance.

5.Are chromatic aberration felt after real wood floor and multilayer floor are spread?
Multiple floors, hardwood floors are made of wood. Trees grow in the natural environment, due to the age of the tree, tree segment, Yin to the sun and other reasons, the color and texture of wood will be different, which is their natural attribute. Also because of the difference of this kind of colour, woodiness floor just appears more vivid and beautiful.

6.How to deal with floor after bubble water?
. When it is found that the floor is soaked in water, the water should be cut off first and the floor should be wiped with a dry mop.
Ask service division to tear open the floor of bubble water in time, face to face fold neat (fold the height that puts depends on the case and decide), press with clog next, natural air is dry. When the number of stacked rows exceeds two, ensure that the space between rows is more than 20 cm for convenient ventilation.
Find seepage sources and repair them in time;
. After the floor is dried (moisture content of solid wood multilayer floor is 5%-14%), the ground moisture content shall be measured when the floor is re-installed. Ordinary ground moisture content is less than 20% (geothermal ground is less than 10%), paving must be paved with PE film, roll up the wall 3-5 cm, and then pavement moisture-proof pad.

7.The reason that wood floor changes color?
. Long-term damp and lack of ventilation in the room leads to fungi and discoloration on the floor;
Water seepage in the room leads to local damp blackening and discoloration of the floor;
. Discoloration of floor caused by continuous strong light exposure or high-temperature baking;
. The floor is partially covered by airtight materials for a long time, resulting in discoloration;

8.Wood floor daily maintenance knowledge?
. The humidity in the room should not be too high, keep the floor dry and smooth, and wipe it with a wrung cotton mop for daily cleaning; In case of stubborn stains, wipe them with neutral cleaning solvent and then wipe them with a twisted cotton mop. Do not use acid, organic solvent or gasoline.
. Pay attention to the daily use of solid wood floor to avoid heavy metal sharp objects, glass tiles, shoe nails and other hard objects scratching the floor; When moving furniture, do not drag on the floor surface; Do not expose the floor to open flames or place high-power electric heaters directly on the floor. Prohibit placing strong acidic and alkaline substances on the floor; Prolonged immersion is absolutely prohibited.
. Avoid water leakage in toilets, kitchens and other rooms. If a large area of water is accidentally soaked, or the office is soaked for a long time, it should be drained as soon as possible after discovery, and let it naturally dry, do not use electric heater drying or exposure to the sun.
. Long exposure to strong sunlight, or the sharp rise and fall of the temperature in the room may cause the aging of the painted surface of solid wood floor in advance, which should be avoided as far as possible.
. If no one lives for a long time, regular ventilation should be provided to ensure that indoor humidity is within the appropriate range to avoid floor deformation or damage.
. The floor mat should be used at the door to avoid sand scratching the board surface.
. Do not place heavy furniture symmetrically.
. Solid wood floor needs to use essential oil to maintain, new flooring, monthly maintenance, two months after half a year maintenance.

news-2-1


Post time: Aug-01-2022